約 6,201,821 件
https://w.atwiki.jp/fns1556/pages/103.html
Cisco Aironet 1. Autonomous Access Pointの基本設定 1.1 ESSIDの設定 ESSIDを「AP0001」として新規作成する。パスフレーズは「testAP0001」でセキュリティはWPA2-PSKを使用する。 この時、ESSIDはステルスモード「no guest-mode」(デフォルト)とする。 dot11 ssid AP0001 vlan 100 authentication open authentication key-management wpa wpa-psk ascii testAP0001 exit WiFiのインターフェースを「アクセスポイント」の役割に設定し、SSIDを関連付ける。 ここで、暗号方式を「AES」として選択する。 interface Dot11Radio0 encryption vlan 100 mode ciphers aes-ccm ssid AP0001 station-role root access-point exit 1.2 SSIDとVLANの関連付け VLAN100となるWiFiインターフェースをブリッジグループと関連付ける。bridge-groupの1は管理用のため、グループ2を使用する。 IRB(BVI)については詳細はIRB 機能によるルータでの VLAN ルーティングおよびブリッジングの理解と設定を参照。 interface Dot11Radio0.100 encapsulation dot1Q 100 bridge-group 2 exit FastEthernetインターフェースにVLAN100のタグを付加し、ブリッジグループと関連付ける。(WLC利用時には、ここがCAPWAPトンネリングになる) interface FastEthernet0.100 encapsulation dot1Q 100 bridge-group 2 exit 参考:Aironet APs Bridge Groups and BVI 参考:Cisco Aironet アクセス ポイント Cisco IOS ソフトウェア コンフィギュレーション ガイド Cisco IOS Release 12.3(4)JA 2 Multi ESSID 1つのAPにてESSIDを複数動作させる!既存でESSID AP0001が動作している環境に、ESSID AP0002を追加する。 Vlanは200、WPA2を利用し暗号化はAESとする。それぞれIEEE802.11g (Dot11Radio0)を利用するものとする。※802.11aはDot11Radio1となる。 また、ESSIDをビーコンにて通知する。 2.1 ESSIDの設定 dot11 ssid AP0002 vlan 200 authentication open authentication key-management wpa mbssid guest-mode (ESSIDの通知、Multi ESSIDで無い場合は「guest-mode」となる) wpa-psk ascii password0002 exit 2.2 Interfaceの設定 ESSID AP0001はbridge-group 1としているため、別のグループ3とする。イメージとして、ブリッジグループ3に「Dot11Radio0.200、FastEthernet0.200」がお互いに所属することでインターフェースを超えたブリッジングが可能となる。また、AESの鍵変更は1時間(3600 seconds)とする 無線インターフェースの設定 interface Dot11Radio0 encryption vlan 200 mode ciphers aes-ccm broadcast-key vlan 200 change 3600 ssid AP0002 exit interface Dot11Radio0.200 encapsulation dot1Q 200 bridge-group 3 exit 有線インターフェースの設定 interface FastEthernet0.200 encapsulation dot1Q 200 bridge-group 3 exit 2.3 Multi ESSIDの有効化 上記のままでは、まだMulti ESSIDが有効となっていない。 AP#show dot11 bssid Interface BSSID Guest SSID Dot11Radio0 xxxx.xxxx.xxx0 No AP0001 Dot11Radio0 xxxx.xxxx.xxx0 Yes AP0002 上記の結果よりESSIDに対するBSSIDが同じになっている。そのため、それぞれ異なるBSSIDとなるようにMulti ESSIDを有効にする。 AP(config)#dot11 mbssid 有効にした後、BSSIDがそれぞれ異なり、動作していることが分かる。 AP#show dot11 bssid Interface BSSID Guest SSID Dot11Radio0 xxxx.xxxx.xxx0 No AP0001 Dot11Radio0 xxxx.xxxx.xxx1 Yes AP0002 3. MAC Address Filtering Aironetにて登録したMACアドレス以外からのアクセスを拒否する。 アクセスリストは700番台を使用する。 ap(config)# access-list ? 1-99 IP standard access list 100-199 IP extended access list 1000-1099 IPX SAP access list 1100-1199 Extended 48-bit MAC address access list 1200-1299 IPX summary address access list 1300-1999 IP standard access list (expanded range) 200-299 Protocol type-code access list 2000-2699 IP extended access list (expanded range) 300-399 DECnet access list 700-799 48-bit MAC address access list 800-899 IPX standard access list 900-999 IPX extended access list dynamic-extended Extend the dynamic ACL absolute timer rate-limit Simple rate-limit specific access list ap(config)# ap(config)# access-list 701 permit xxxx.xxxx.xxxx 0000.0000.0000 ap(config)# dot11 association mac-list 701 MACアドレスフィルタリング有効化後、無線LANクライアントがアソシエーション出来ていることを確認する。 ap#show dot11 associations 802.11 Client Stations on Dot11Radio0 SSID [AP0001] MAC Address IP address Device Name Parent State xxxx.xxxx.xxxx 192.168.1.1 unknown - self Assoc Cisco Wireless LAN Controller 1. WLCの基本設定 (Cisco Controller) Welcome to the Cisco Wizard Configuration Tool Use the - character to backup Would you like to terminate autoinstall? [yes] AUTO-INSTALL starting now... rc = 0 System Name [Cisco_xx xx xx] (31 characters max) AUTO-INSTALL no interfaces registered. AUTO-INSTALL process terminated -- no configuration loaded - Invalid response System Name [Cisco_xx xx xx] (31 characters max) wlc-01 Enter Administrative User Name (24 characters max) admin Enter Administrative Password (3 to 24 characters) ********* Re-enter Administrative Password ********* Management Interface IP Address 172.16.1.250 Management Interface Netmask 255.255.255.0 Management Interface Default Router 172.16.1.254 Management Interface VLAN Identifier (0 = untagged) 1001 Management Interface Port Num [1 to 8] 1 Management Interface DHCP Server IP Address 172.16.1.254 AP Manager Interface IP Address 192.168.8.250 AP Manager Interface Netmask 255.255.255.0 AP Manager Interface Default Router 192.168.8.254 AP Manager Interface VLAN Identifier (0 = untagged) 8 AP Manager Interface Port Num [1 to 8] 1 AP Manager Interface DHCP Server (172.16.1.254) 192.168.8.254 Virtual Gateway IP Address 1.1.1.1 Mobility/RF Group Name MGroup-01 Network Name (SSID) test-ssid Configure DHCP Bridging Mode [yes][NO] yes Warning! Enabling Bridging mode will disable Internal DHCP server and DHCP Proxy feature. May require DHCP helper functionality on external switches. Allow Static IP Addresses [YES][no] yes Configure a RADIUS Server now? [YES][no] no Warning! The default WLAN security policy requires a RADIUS server. Please see documentation for more details. Enter Country Code list (enter help for a list of countries) [US] J2 Enable 802.11b Network [YES][no] yes Enable 802.11a Network [YES][no] yes Enable 802.11g Network [YES][no] yes Enable Auto-RF [YES][no] yes Configure a NTP server now? [YES][no] no Configure the system time now? [YES][no] no Warning! No AP will come up unless the time is set. Please see documentation for more details. Configuration correct? If yes, system will save it and reset. [yes][NO] yes 上記の初期設定後のconfig (Cisco Controller) config paging disable (Cisco Controller) show run-config commands 802.11a cac voice tspec-inactivity-timeout ignore 802.11a cac video tspec-inactivity-timeout ignore 802.11a cac voice sip codec g711 sample-interval 20 802.11a cac voice sip bandwidth 64 sample-interval 20 802.11a cac voice stream-size 84000 max-streams 2 802.11b cac voice tspec-inactivity-timeout ignore 802.11b cac video tspec-inactivity-timeout ignore 802.11b cac voice sip codec g711 sample-interval 20 802.11b cac voice sip bandwidth 64 sample-interval 20 802.11b cac voice stream-size 84000 max-streams 2 802.11h channelswitch enable 0 aaa auth mgmt local radius location rssi-half-life tags 0 location rssi-half-life client 0 location rssi-half-life rogue-aps 0 location expiry tags 5 location expiry client 5 location expiry calibrating-client 5 location expiry rogue-aps 5 advanced eap bcast-key-interval 3600 Cisco Public Safety is not allowed to set in this domain ap syslog host global 255.255.255.255 cdp advertise-v2 enable country J2 database size 2048 dhcp proxy disable dhcp opt-82 remote-id ap-mac local-auth method fast server-key **** interface address ap-manager 192.168.8.250 255.255.255.0 192.168.8.254 interface address management 172.16.1.250 255.255.255.0 172.16.1.254 interface address virtual 1.1.1.1 interface dhcp ap-manager primary 192.168.8.254 interface dhcp management primary 172.16.1.254 interface vlan ap-manager 8 interface vlan management 1001 interface port ap-manager 1 interface port management 1 load-balancing aggressive enable load-balancing window 5 apgroup add default-group apgroup interface-mapping add default-group 1 management wlan apgroup nac-snmp disable default-group 1 memory monitor error enable memory monitor leak thresholds 10000 30000 mesh security rad-mac-filter disable mesh security rad-mac-filter disable mesh security eap mgmtuser add admin **** read-write mobility group domain MGroup-01 mobility dscp 0 network multicast mode multicast 0.0.0.0 network ap-priority disabled network rf-network-name MGroup-01 paging disable radius fallback-test mode off radius fallback-test username cisco-probe radius fallback-test interval 300 rogue ap ssid alarm rogue ap valid-client alarm rogue adhoc enable rogue adhoc alert rogue ap rldp disable rogue detection monitor-ap report-interval 10 Not Supported. snmp version v2c enable snmp version v3 enable snmp snmpEngineId xxxxxxxxxxxxxxxxxxxxxxxx switchconfig strong-pwd case-check enabled switchconfig strong-pwd consecutive-check enabled switchconfig strong-pwd default-check enabled switchconfig strong-pwd username-check enabled sysname wlc-01 trapflags mesh excessive hop count disable trapflags mesh sec backhaul change disable wlan create 1 test-ssid test-ssid wlan nac snmp disable 1 Max no. of clients 0 wlan multicast interface 1 disable wlan session-timeout 1 1800 wlan h-reap learn-ipaddr 1 enable wlan wmm allow 1 wlan security wpa akm ft reassociation-time 20 1 wlan security wpa akm ft over-the-air enable 1 wlan security wpa akm ft over-the-ds enable 1 wlan enable 1 license agent default authenticate none license boot base WMM-AC disabled coredump disable media-stream multicast-direct disable media-stream message url media-stream message email media-stream message phone media-stream message note denial media-stream message state disable 802.11a media-stream multicast-direct enable 802.11b media-stream multicast-direct enable 802.11a media-stream multicast-direct radio-maximum 0 802.11b media-stream multicast-direct radio-maximum 0 802.11a media-stream multicast-direct client-maximum 0 802.11b media-stream multicast-direct client-maximum 0 802.11a media-stream multicast-direct admission-besteffort disable 802.11b media-stream multicast-direct admission-besteffort disable 802.11a media-stream video-redirect enable 802.11b media-stream video-redirect enable (Cisco Controller) TFTPでconfigバックアップしたもの config certificate generate webadmin config interface port management 1 config interface port ap-manager 1 config interface address management 172.16.1.250 255.255.255.0 172.16.1.254 config interface dhcp management primary 172.16.1.254 config interface vlan management 1001 config interface address virtual 1.1.1.1 config interface address ap-manager 192.168.8.250 255.255.255.0 192.168.8.254 config interface dhcp ap-manager primary 192.168.8.254 config interface vlan ap-manager 8 config country J2 config mobility group domain MGroup-01 config sysname wlc-01 config database size 2048 config license boot base config network rf-network-name MGroup-01 config dhcp proxy disable bootp-broadcast disable config mgmtuser add encrypt admin xxxxxx xxxxxx xxxxxx xxxxxx read-write config advanced 802.11a channel add 36 config advanced 802.11a channel add 40 config advanced 802.11a channel add 44 config advanced 802.11a channel add 48 config advanced 802.11a channel add 52 config advanced 802.11a channel add 56 config advanced 802.11a channel add 60 config advanced 802.11a channel add 64 config advanced 802.11b channel add 1 config advanced 802.11b channel add 6 config advanced 802.11b channel add 11 config wlan wmm allow 1 config wlan mfp client enable 1 config wlan security wpa enable 1 config wlan exclusionlist 1 1 config wlan broadcast-ssid enable 1 config wlan interface 1 management config wlan session-timeout 1 1800 config wlan create 1 test-ssid test-ssid config wlan mobility foreign-map add config wlan enable 1 config 802.11a 11nsupport a-msdu tx priority config 802.11a cac voice sip bandwidth 64 sample-interval 20 config 802.11a cac voice sip codec g711 sample-interval 20 config 802.11b 11nsupport a-msdu tx priority config 802.11b cac voice sip bandwidth 64 sample-interval 20 config 802.11b cac voice sip codec g711 sample-interval 20 config 802.11b 11gsupport enable transfer upload filename wlc_config.cfg transfer upload datatype config transfer upload serverip 172.16.1.1 transfer upload path / transfer download filename wlc_config.cfg transfer download serverip 172.16.1.1 transfer download path / 1.1. APのチャネル固定 (Cisco Controller) config 802.11a disable AP01 (Cisco Controller) config 802.11a channel ap AP01 52 (Cisco Controller) config 802.11a enable AP01 (Cisco Controller) 1.2. APの動的チャネル変更(Globalモード) (Cisco Controller) config 802.11a disable AP01 (Cisco Controller) config 802.11a channel ap AP01 global (Cisco Controller) config 802.11a enable AP01 (Cisco Controller) 1.3 ClientExclusionによる接続問題? 無線LANのアソシエーションを頻繁に行っていたら、繋がらなくなったのでログをアップpeap-notconnect.zip 1-debug_dot1x_ok.log 問題なくPEAP認証出来る状態。 2-debug_dot1x_no_radius_request-ng.log 認証が出来なくなった時のログ。(接続・切断を連打したことにより繋がらなくなる)この時、Radius Requestが送信されず、また、異なるSSIDのWPA2-PSKすらも認証出来なくなった。そのため、Client Exclusionによる影響?かと思われる。(但し、WLAN Profile自体でのClient Exclusionは有効・無効どちらでも問題が発生することを確認・・・) 3-debug_dot1x_no_radius_request-ng_no_client_exclusion-ok.log Client Exclusionを無効化して問題なく接続が復旧した時のログ。(復旧に時間が掛かる?)
https://w.atwiki.jp/nicoratch/pages/1066.html
概要 LPD8 ベロシティ対応のコンパクトMIDIコントローラー。 USB端子が破損しやすいとレビューあり。 サウンドハウスレビュー http //www.soundhouse.co.jp/products/detail/item/144302/ LPD8の主な特長 USB - MIDIコントローラー LED内蔵ベロシティ対応の8ドラムパッド(プログラムチェンジ情報、コントロールチェンジ情報も送信可能) アルペジエーター、サスティンボタン、オクターブアップ・ダウン、タップテンポ・コントロール Mac/PCでドライバー不要なプラグ&プレイ対応 バックパックやラップトップ・バッグに収まるコンパクトサイズ 4つのメモリ・バンク エディターソフト(Mac/PC)で各パラメーターを設定可能 USBバスパワー駆動 ※詳細スペック情報なし。 価格 ¥ 5,980 LPD8 http //akai-pro.jp/lpd8/ LPD8 Wireless 2016年12⽉23⽇(⾦)発売。 LPD8 Wirelessの主な特長 MIDI over Bluetooth機能で、MacやiPhone/iPadと【ワイヤレスで接続可能なMIDIパッドコントローラー】 USB-MIDI端子(USB-B端子)も搭載、MacやWindows、iPhone/iPadとドライバーをインストールすることなく【USBケーブルでも使用可能】 ノート情報とプログラムチェンジ情報を送信可能な8つの【バックライト搭載ベロシティ対応のドラムパッド】(2パッドバンク) 様々なパラメーターをコントロール可能な【8つのアサイナブル・ノブ】 セッティングを記憶可能な【4つのプリセット・プログラム】 エディターソフトウエア(Mac/Windows)付属(ダウンロード提供) USBバスパワーまたは単3乾電池3本による動作 +スペック表・LPD8 Wireless 仕様 コントローラー: (8)バックライト搭載ベロシティ対応バッド (2)パッドバンク (8)270°回転アサイナブル・ノブ (1)Full Levelボタン (1)Note Repeatボタン (1)Tap Tempoボタン ノートリピート機能: タイムディビジョン:1/4、1/4三連、1/8、1/8三連、1/16、1/16三連、1/32、1/32三連 モード:トグル、モーメンタリー スウィング:50%、56%、58%、60%、62% テンポ:30〜240BPM(インターナルシンク)、外部同期可能(エクスターナルシンク) プログラム: エディターソフトによる設定を4つのプリセット・プログラムに保存可能 Bluetooth: プロファイル:Bluetooth Low Energy(BLE) 到達距離:約30m 端子: (1)USB端子(USB-B端子) 電源: USBバスパワー、または単3乾電池3本 システム要件: 【USB有線接続】 Mac:Mac OS X 10.9以上 iOS:iOS 8.0以上(別途Apple社USBカメラコネクションキットが必要です) Windows:Windows 7以上 【Bluetoothワイヤレス接続】 Mac:Mac OS X 10.10以上、Bluetooth 4.0に対応したMac iOS:iOS 9.0以上、Bluetooth 4.0に対応したiPhone/iPad サイズ: 約311 x 110 x 34mm(W x D x H) 重量: 約0.45kg ※ 仕様は断りなく変更される場合がございます。 販売価格 (税抜)¥10,926 (税込 ¥11,800)⇒価格改定(税抜)¥8,778 (税込 ¥9,480) JANコード:0694318020951 LPD8 Wireless http //akai-pro.jp/lpd8-wireless/
https://w.atwiki.jp/ameba_pigg/pages/2326.html
Wireless Vacuum vacuumcleaner_wireless_0905.swf Catalog Order Unisex Interior Electronics 80 Ameba Gold http //info.pico.ameba.net/2010/03/02/lets-redecorate-your-room/
https://w.atwiki.jp/mrfrtech/pages/32.html
Market Analysis The In-Building Wireless Market is expected to grow at a CAGR of 12.30 % by2027, reaching USD 19.1 billion in the forecast period. In enterprise networks, wireless networking has made great advances. These wireless networks connect mobile phones to the public switched telephone network and give internet access via a local area network. Rather than the conventional cellular networks separate interface networks, the wireless networks will converge to service both internet and telephone devices, resulting in increased efficiency and low cost. Wireless LAN and wireless cellular have been regarded as overlay networks in businesses. It has grown in popularity as a major phone and data access point within the building. The increased use of wireless in the business world has changed the requirements for in-building wiring as well as the facilities required in telecommunications facilities. There is a growing demand for consistent cell phone service in business spaces. In-build wireless is a networking solution that enables the upgrading and deployment of wireless connections within an office building or other large commercial enterprise. The major growth driver of the In-building wireless market is the increased acceptance of in-building wireless technologies such as higher data rates, increased use of mobile devices, the adoption of "bring your own device" culture in offices, schools, and other environments, lower-cost network infrastructure for wireless systems, improved wireless network quality of service, and improved wireless in-building coverage. However, lesser operational knowledge in the wireless system due to complex technology can be a restraining factor for the market growth. But the current pandemic situation is also creating many opportunities in the global market due to wireless communications to remote locations. Request a Free Sample @ https //www.marketresearchfuture.com/sample_request/10479 Market Segmentation According to the global In-building wireless market analysis report, the market is classified into component, business model, venue, end-user, and region. Further, these segments are against segregation into various market elements. On the basis of components, the in-building wireless market again segmented into infrastructure and services. Moreover, the infrastructure segment is divided into DAS and small cells once more. The business model segment has further divided the in-building wireless market into service providers, enterprises, and neutral host operators. Similarly, the venue segment is again classified into large venues, medium venues, and small venues. According to the end user segment, the in-building wireless market is sub-segmented into government, manufacturing, transportation and logistics, education, retail, hospitality, healthcare, and others. Regional Analysis North America, Europe, Asia-Pacific, the Middle East and Africa, and South America were all studied for the global in-building wireless market. Based on this global market analysis, North America is estimated to lead the global in-building wireless market in terms of the growing demand for distinct and defined network coverage. Moreover, the Asia-pacific market region is also expected to grow at a faster pace in the forecast period due to increasing economic developments and building awareness in the in-building wireless techniques. Key Players The key players of the global in-building wireless market are Nokia ( Finland ) , Ericsson ( Sweden ) , Huawei ( China ) , ZTE( China ) , NEC ( Japan ) , CommScope ( US ) , Corning ( US ) , Axell Wireless ( UK ) , Comba Telecom ( Hong Kong ) , Samsung ( South Korea ) , SOLiD ( South Korea ) , Dali Wireless ( US ) , Zinwave ( US ) , ADRF ( US ) , ip.access ( UK ) , Airspan ( US ) , Contela ( South Korea ) , Fujitsu ( Japan ) , BTI Wireless ( US ) , Bird ( US ) , Accelleran ( Belgium ) , Baicells Technologies ( US ) , Qucell ( South Korea ) , Casa Systems ( US ) , CommAgility ( UK ) , Galtronics ( Canada ) , G-Wave Solutions ( US ) , HUBER+SUHNER ( Switzerland ) , JMA Wireless ( US ) , Microlab ( US ) , Nextivity ( US ) ,Sarcomm ( Taiwan ) , PCTEL ( US ) , Whoop Wireless ( US ) , and Westell Technologies ( US ) . Industry News In December 2021, Nokia announced to have deployed a 5G private wireless network for Volkswagen s pilot project in Germany, which would help with supporting industrial connectivity at the product development center. In October 2021, Ericsson and PowerLightshowed, the world s first wirelessly powered 5G base station. Browse Full Report Details @ https //www.marketresearchfuture.com/reports/in-building-wireless-market-10479 Table of Contents 1 Executive Summary 2 Scope of The Report 2.1 Market Definition 2.2 Scope of The Study 2.2.1 Research Objectives 2.2.2 Assumptions Limitations 2.3 Market Structure Continued… Similar Report** Passport Radar Market https //www.marketresearchfuture.com/reports/passport-reader-market-5929 Internet of things (IoT) Market https //ictmrfr.blogspot.com/2022/04/internet-of-things-market-growth-key.html B2B Telecommunication Market https //www.scutify.com/articles/2022-04-12-b2b-telecommunication-market-analysis--geographic-growth-opportunities-for-it-security-and-data- Cash Management System Market https //market-research-future.tribe.so/post/cash-management-system-market-size-receives-a-rapid-boost-in-economy-due-to--625d5382d24f49591bd3befb Open Source Intelligence (OSINT) Market By Security Type (Human Intelligence, Content Intelligence, Dark Web Analysis, Link/Network Analysis, Data Analytics, Text Analytics, Artificial Intelligence, Big Data, Others), Technology (Bid Data Software, Video Analytics, Text Analytics, Visualization Tool, Cyber Security, Web Analysis, Social Media Analysis, Others), Application (Military Defense, Homeland Security, Private Sector, Public Sector, National Security, Others) About Market Research Future At Market Research Future (MRFR), we enable our customers to unravel the complexity of various industries through our Cooked Research Report (CRR), Half-Cooked Research Reports (HCRR), Raw Research Reports (3R), Continuous-Feed Research (CFR), and Market Research Consulting Services. Contact Market Research Future (Part of Wantstats Research and Media Private Limited) 99 Hudson Street, 5Th Floor New York, NY 10013 United States of America 1 628 258 0071 (US) 44 2035 002 764 (UK) Email sales@marketresearchfuture.com Website https //www.marketresearchfuture.com #market #research #industry #data #report #share #digital #gnews Plugin Error キーワードを入力してください。 #trend #future #analyis #industryreport #industrygrowth #demographic #strategy #manegment
https://w.atwiki.jp/bayashidayo/pages/18.html
wired-cum-wireless scenarios 今までに説明されたMNは、マルチホップのAd-hocネットワークか無線LANのシミ ュレーションを主にサポートする。しかし、複数の無線LANを有線ノードを経由 して接続するトポロジーをシミュレーションする必要があればよい、または無線 ノード上でMIPを動作させるにはどうなるだろうか?。CMUの無線モデルで作られ た拡張の利用を許す。 有線兼無線シナリオの向かい合う主な問題はルーティングです。nsではルーティ ング情報はトポロジーの接続性を基に生み出される、つまりノードがどのように 他のあるLinksを経由するかです。MNはリンクにおいて、他の方法のコンセプト を持たない。無線環境で利用するルーティングプロトコルはルートパケット自身 の中にありますその2種類のノードの間で拡張をするにはパケットをどうしたら よいのでしょうか?。 ノードが無線有線ドメインのゲートウェイの役割をするとき、BaseStationNode の作成を宣言する。BaseStationNodeは基本的には、階層ノード16.1(HierNode) とMobileNodeの間です。ベースステーションノードは、中や外の無線ドメインの 配送パケットに応答します。階層ルーティングの要求を達成する必要がある。 それぞれのドメインはベースステーションに沿ってユニークなドメインアドレス をそれに割り当てたい。無線ノード行きの全てのパケットは、結局はパケットを 目的地に渡すことで無線ノードの接続しているドメインのベースステーションに 到達するだろう。MNのルートパケットはベースステーションノードの外側の無線 ドメインに向かう。ベースステーションは有線の目的地へパケットを転送する方 法を知っている。 Figure 16.3 Schematic of a baseStationNode basestation wired-cum-wirelessシナリオのMNは階層型アドレスとルーティングが必要です。 MNは完全にBaseStationNodeのように見えます。しかしながら、SRノードは自身 のhier-addressを持っていても単純に、どのdemuxesアドレスも要求しないし、 高いルーティング16.2をサポートする必要としない必要がある。 もし、目的地がサブネットの外側なら、DSDVエージェント内で転送パケットをチ ェックして監視する。だとすれば、ベースステーションへのパケット転送を試み る。ベースステーションへのルートが無い場合、パケットロスが発生する。他の 方法として、パケットを次のホップのベースステーションの方へ転送する。ベー スステーションのclassifiersにより、有線ネットワークの方に転送する。 外部のサブネットに向かうパケットを受信したDSRエージェントは、ベースステ ーションへのルートを知らない場合、ベースステーションにルートリクエストを 送信する。データパケットはベースステーションからのルート応答を待っている 間、一時的に記憶される。応答を受け取ると、パケットはヘッダ内のルーティン グ情報と共にベースステーションの方へ送信される。ベースステーションのアド レスのdemuxesルートは、現在有線ネットワークに向いている。 wired-cum-wirelessシミュレーションの例は tcl/ex/wired-cum-wireless-sim.tclで見ることができる。wired-cum-wireless を実装したメソッドはtcl/lib/ns-bsnode.tcl, tcl/mobility/{com.tcl,dsr.tcl, dsdv.tcl}, dsdv/dsdv.{cc,h} とdsr/dsragent.{cc,h}で定義される。
https://w.atwiki.jp/bayashidayo/pages/16.html
The basic wireless model in ns この無線モデルは本質的にはMNを中心に成り立ち、その上さらなる特徴として、 マルチホップAd-hocネットワークや無線ネットワークなどのシミュレーションを 許す。MNもオブジェクトは分割オブジェクトです。C++の MobileNode../ns-2/mobilenode.hはNode../ns-2/node.hに由来する。 Nodeの詳 細はチャプター5を参照。したがってMNは与えられたトポロジー内を動く能力、 無線チャンネルから信号を受信し送信する能力のような、無線とMNの機能を付加 した標準的な Nodeオブジェクトです。もっとも、これらの間のメジャーな違い は、 MNは他のnodeかmobilenodeにLinksする手段によって接続されないことです。 このセクションでは、MNの内部の、ルーティングメカニズム、AODV,DSDV,TORAや DSRのルーティングプロトコル、MNにおいてチャネルアクセスを許可するネット ワークスタックの作成、それぞれのスタック構成の簡単な記述、トレースのサポ ートと、無線シミュレーションの移動/トラフィックシナリオの作成を説明する でしょう。 16.1.1Mobilenode creating wireless topology? 16.1.2Creating Node movements? 16.1.3Network Components in a mobilenode? 16.1.4Different MAC layer protocols for mobile networking? 16.1.5Different types of Routing Agents in mobile networking? 16.1.6Trace Support? 16.1.7Revised format for wireless traces?16.1.7.1Explanation of new trace format? 16.1.8Generation of node-movement and traffic-connection for wireless scenarios?16.1.8.1MobileNode Movement? 16.1.8.2Generating traffic pattern files?
https://w.atwiki.jp/bayashidayo/pages/13.html
多分間違ってる Phy/WirelessPhy set bandwidth_ 54Mb # 54 Mbps bandwidth(物理層帯域幅) Mac/802_11 set dataRate_ 54Mb # 54 Mbps for data(MAC層ユニキャスト) Mac/802_11 set basicRate_ 54Mb # 54 Mbps for broadcasts(MAC層ブロードキャスト時) 802.11gの設定(メーリングリストから抜粋) あってる保証無し #define DSSS_CWMin 15 #define DSSS_CWMax 1023 #define DSSS_SlotTime 0.000009 // 9us #define DSSS_CCATime 0.000004 // 4us #define DSSS_RxTxTurnaroundTime 0.000005 // 5us #define DSSS_SIFSTime 0.000010 // 10us #define DSSS_PreambleLength 96 // 96 bits or 120 bits #define DSSS_PLCPHeaderLength 24 // 4 us #define DSSS_PLCPDataRate 6.0e6 // 6Mbps #define DSSS_MaxPropagationDelay 0.0000005 // 0.5us これをどうやってスクリプトに組み込むか? 802.11のMAC層を定義しているファイルの中身(/mac/mac-802_11.h) #define DSSS_CWMin 31 #define DSSS_CWMax 1023 #define DSSS_SlotTime 0.000020 // 20us #define DSSS_CCATime 0.000015 // 15us #define DSSS_RxTxTurnaroundTime 0.000005 // 5us #define DSSS_SIFSTime 0.000010 // 10us #define DSSS_PreambleLength 144 // 144 bits #define DSSS_PLCPHeaderLength 48 // 48 bits #define DSSS_PLCPDataRate 1.0e6 // 1Mbps #define DSSS_MaxPropagationDelay 0.000002 // 2us を書きかえるのかも・・・? チャネルの分割(3つのチャネルに分割) オプションの設定で set val(chan) Channel/WirelessChannel ※このまま”node-config”で”-channel $val(chan)”とやると警告がでる 結果には影響ないけど警告の対策も含めて以下のように宣言を変える set chan_1 [new $val(chan)] set chan_2 [new $val(chan)] set chan_3 [new $val(chan)] ↑で3つのチャネルを宣言(chan_1~3) それぞれのチャネルを割り当てたいノードごとに node-config -channel chan_1 $ns_ node ~ node-config -channel chan_2 $ns_ node ~ node-config -channel chan_3 $ns_ node ~ のようにやるとエラーも出ないし、それぞれのノードに別々のチャネルを割り当てられる
https://w.atwiki.jp/kapper1224/pages/112.html
AndroidやiOS用のDVDプレイヤーです。 こちらに記載しましたのでご一読を。 安くなった3,980円 Logitec Wireless DVD Playerでジャンクスマホ、タブレットからDVD再生してみた。Android4.2、iOS8.0以降
https://w.atwiki.jp/divadiva/pages/17.html
OpenSolarisはWiFi環境にも対応している。 が、実際に設定を行ってみると、すんなりいかないことも多いのではないだろうか。OpenSolarisがどうこう、というよりも、一般的な無線LAN設定の問題、もあるわけだが、とにもかくにも、実際につながるまで発生した問題などを書いておく。 デバイス設定 まず最初にしなければならないのは、Wireless NIC Driverのインストールである。 なので自分が使用しているWiFi NICがどのようなチップを使用しているのかを知らなければならない。そしてそのチップ用のドライバが入手できなければ話にならん!と。 私のマシンはIntel Pro Wireless 2100Bというチップを使ったNICを内蔵しているので、OpenSolarisのサイトから対応するドライバ(ipw)をダウンロードしてインストールした。 OpenSolarisのサイトにはマシン再起動しなくても認識されると書いてあるが、私の場合はインストール直後に、 # ifconfig ipw0 plumb しても認識されなかった。 だが、再起動後にifconfigコマンドを実行すると、無事認識され、マシンのWiFiアンテナランプが点灯した。 (注意 2006/07/23) この時点でエラーが発生してうまくいかないことがある。 ドライバインストール時に「インストールはしたけどattachできねーよ」といわれる ifconfig ipw0 plumb すると file not found などというエラーが出る OS起動時に undefined symbol error が発生する(mac_freeがどうのこうの) これらはカーネルのbuildバージョンとドライバがマッチしていない場合に出てくるのだ! たとえばipw-0.5のドライバはon build 44以上を要求しているのだ。カーネルが古い場合はipwドライバも過去のものを使おう。 WiFi設定 デバイスが認識されたら、wificonfigコマンド(これもOpenSolaris.orgからパッケージを入手してインストールしておく)でWiFiの接続設定プロファイルを設定する。 ESSID、暗号化方式、認証方式などを設定するわけだが、一つ注意点。ipwのmanページにも記述があるが、現時点ではSharedKey認証がサポートされていない。認証方式としてはOpenSystem方式を利用することになるので、AP側の設定を、SharedKey固定などにしておくと接続ができないので注意である。 暗号化についてはWEPのみサポートされており、WEPキーは40bitまたは128bitのASCII文字列あるいは16進文字列が使用可能である。 また、wificonfigではなくGUIの設定ツールinetmenuを使用する場合、最近のAPが備えるESSID秘匿モードには対応しないので注意したい。wificonfigのscanコマンドで取得できないESSIDはinetmenuの設定対象にならないので、そういう場合はinetmenuではなくwificonfigで設定しなければならない。 で、例えば下記のコマンドで接続ができる。 手順としては、まずプロファイルを作成し、次にネットワークインタフェースに対してプロファイルを割り当てる、というかたちである。 まずはプロファイルの作成。ESSIDがプロファイル名となる。下記コマンドでは、WEP暗号化方式を指定し、WEPキー1に対してキー文字列を割り当て(1~4まで指定可能)、キー1を使用することを宣言している。 # wificonfig createprofile essid=YOUR_ESS_ID encryption=WEP wepkey1=YOUR_WEB_KEY wepkeyindex=1 プロファイル自体はいくつでも作成できる。作成したプロファイルは下記のコマンドで確認可能である。 # wificonfig showprofile そしてプロファイル名をネットワークインタフェースipw0に割り当てる。インタフェース名は、使用するWirelessデバイスドライバによって異なる。 # wificonfig -i ipw0 connect YOUR_PROFILE_NAME この後、 # wificonfig -i ipw0 showstatus として、linkstatus connected と表示されていれば、とりあえず接続だけは成功したことになる。 もしそれでもネットワークがうまくつながらなかった場合は、ifconfigコマンドで一度WiFiインタフェースをDOWNさせ、再度UPさせてみよう。 inetmenuに注意! GUIツールのinetmenuには注意が必要。 svcsコマンドでも確認できるが、こいつはboot時にdhcpサーバにアクセスに行く。boot時にはAPに接続されていないので、dhcpサーバへのアクセスに失敗し、結果としてIPアドレスが不明な/etc/hostsファイルが生成される。 (APに接続するには wificonfig -i ipw0 connect~ コマンドが実行されなければならないが、通常boot up時にこのコマンドが自動実行されることは無い) たとえば/etc/hostsにstatic addressとマシン名を書いてあったとしても、それが削除されて、対応するIPアドレスが空になってホスト名だけが記述された、不正な/etc/hostsに書き換えられてしまう。 この動作は将来改善される可能性があるようだが、現時点ではどうしようもないので、inetmenuをsvcadmなどでdisableしておくことをおすすめする。 詳しくは、OpenSolaris.orgのDiscussonsの 「Automatic WiFi Connect on boot」スレッドを参照。 最終的にこんなんなりました! このところ出張でPCを持ち歩くことが多くなり、NW環境を頻繁に切り替えるようになった。また、当初はinetmenuふざけるな的な感じでいたわけだが、その後バージョンも上がり、変な動きをすることはなくなった(みたい)。 なので結局inetmenuを全面的に使うことになった。 ホテルのネット接続環境は通常DHCPになるが、その環境はホテルによって微妙に異なる。当初は手作業で設定していたが、環境毎の「くせ」に合わせるのが非常にめんどくさいので、まぁやはりinetmenuが良いのである。 で、DHCPの設定についてもinetmenuで選択すればいいだけなのでとても簡単なのだが、やはりinetmenuの「くせ」がこれまたあったりするので、私は少しいじっている。 詳細についてはこちらのinetmenuの項目を参照。 [PR] 介護資格
https://w.atwiki.jp/motomods/pages/17.html
商品紹介 標準のStyle Shellとほぼ同じ厚さで無線充電機能と赤外線送信機能を搭載したMods。 機能を絞る一方で、外観への影響を抑えているのが特長。 出資タイプ Flexible Funding(目標金額に達しなくてもプロジェクト実行)Closed(期間終了) PERKS(報酬)一覧 名前 金額 内容 限定数 20% OFF! $10 将来の販売時に20%割引 ∞ Thanks and Gratitude $10 なし ∞ Wireless Charging Style Shell $35 Mods本体(無線充電機能のみ) ∞ Wireless and IR style shell $45 Mods本体(赤外線送信機能付き) ∞ Two Wireless charging shells $65 Mods本体*2(無線充電機能のみ) ∞ Two wireless and IR shells $85 Mods本体*2(赤外線送信機能付き) ∞ More Thanks and Gratitude $100 なし ∞ リンク