約 6,196,153 件
https://w.atwiki.jp/eagleeye/pages/19.html
Packing info Packaging Type Gift Box MSRP $59.99 Penguin SKU 215PUPP Warranty Period 1 Year Unit Dimensions 5.5X5X2.50 in. Unit Weight 0.68 lbs. Master Unit Count 50 Master Dimensions 26.18 x 13.58 x 12.20 in. Master Weight 33lbs. Inner Unit Count N/A Inner Dimensions N/A Inner Weight N/A Features 1. Converts most wired USB HID 2.0 Keyboard and Mouse into a PS3 Controller. 2. Customize all of your PS3 controller buttons to your Keyboard Mouse. (Right Analog stick defaults to mouse movement) 3. Highest possible refresh rate resulting in a fluid, delay free mouse movement. 4. Store up to 2 Key Mapping schemes. 5. Quick Easy setup gets you started within minutes. 6. 13ft. long USB cable for a flexible setup. 7. Compatible with all PS3 console versions and all PS3 titles. Best for, but not limited to, First-Person shooting games. 8. Programmable Macro Functions to turn any single key into a combination of moves. Store up to 4 combo sets. 9. Turbo option for X, triangle, square, circle, L1, L2, R1, R2 buttons 10. Plug directly into your PS3 and auto detect as a PS3 controller. 11. PC only required during setup, not required during game play. Requirements • PC with at least 1 USB input to run controller scheme mapping program • 1 USB Mouse • 1 USB Keyboard System Requirements Windows XP or later 512 MB RAM 2MB free HD space 4×CD-ROM drive Must use 1 USB HID Keyboard and 1 USB HID Mouse in conjunction with the Eagle Eye Not compatible with most wireless Keyboard and Mouse devices.* Update Eagle Eye users have discovered compatible wireless devices. Check our forum to see which keyboards and mice are compatible. For Eagle Eye related questions, please write to EagleEye.help@gmail.com
https://w.atwiki.jp/fragnstein/pages/27.html
公式HP 公式のセットアップ説明 ビデオ 1.公式から新しいFW ドライバを落とす 2010/11/7の場合はVer2.0なので Firmware 2.0 BETA update pack (Beta 10.15.2010)というファイルを 公式のセットアップ説明 ビデオページからダウンロード、解凍する 2.ドライバを更新する 1.Eagle Eye背面のボタンをPROGRAMに設定しておく。 2.Eagle EyeをUSBに差し込む。 3.スタート→コントロールパネル→管理ツール→コンピュータの管理を起動する 4.デバイスマネージャを選択、USBコントローラーのツリーを展開 5.事前にインストールされているドライバ（BYFF~~SS EZ-OTGだかなんだか）を選択し ドライバの更新ボタンを押す 6.「いいえ、今回は接続しません」を選ぶ 7「一覧または特定の場所からインストール」を選ぶ 8.「次の場所を含める」で先ほどDLしたファイルの EEC Firmware 2.0内にあるDriversを選択 9.次へを押す 10.警告が出るがok（左のボタン） 2.ドライバを更新出来たかの確認 USBコントローラーのツリーに「Cypress USB EZ-OTG Device」があれば完了 Firmware を入れる 1.Eagle Eye背面のボタンをPROGRAMに設定しておく。 2.Eagle EyeをUSBに差し込む。 3.EEC Firmware 2.0のフォルダにある「bash_env1.bat」起動 4.Eagle Eye背面のボタンをPLAYに設定しなおす、 この時、USBは接続状態を維持したまま変更すること 5.C WINDOWS\system32\cmd.exeに「qtui2c eagle1007.bin f」と打ち込みエンター 1～4順番にしていないとこの時「そんなUSBないよ」的なエラーが出る 6.Please weitの表記が出たら成功、二分ほど待つ 7.return statusの表記が出たらFWのアップデートが終了 突貫で作った、間違ってるところがあったらたのんだ。英語読めない。 他にも色々設定があるから偉い人追記頼んだ 名前 コメント
https://w.atwiki.jp/eagleeye/
Eagle Eye Converter@wiki JPへようこそ ！注意！ このサイトの記載内容は、古い情報です(2012.2.20現在）。設定方法などは公式サイトをお読みください。 Penguin Unitedの製品 Eagle Eye Converter for PlayStation 3(以下EEC)にまつわる情報をまとめています。 このサイトはユーザーのみなさんの協力により成り立っています。是非補完/翻訳作業にご協力下さい。編集の利用ガイドはこちら。ルールを守って素晴らしいサイトにしましょう。 ！注意！ このサイトの記載内容は、古い情報です(2012.2.20現在）。設定方法などは公式サイトをお読みください。 Introduction EECとは 商品概要・動作環境 Help 購入手引き セットアップ、FW Update よくある質問 2chスレからのTips EEC ForumからのTips Eagle Edit Software Eagle Eye Edit Software Download V1.0 (Updated 8.18.2010) Eagle Eye Edit Software V.2.0 Download Only EagleEdit20.RAR (Updated 10.12.2010) Firmware 2.0 Final Release pack(11/12/10) Update内容 Firmware 2.0 Final Release pack(11/12/10) Link Penguin United EEC Forum EEC Q A EEC Supportcve 2chスレ：マウス型コントローラ＆アダプタ総合part 5
https://w.atwiki.jp/eagleeye/pages/26.html
Firmware Update Procedures Note The EagleEye Converter (EEC) currently does not support the firmware update procedure for Windows 64-bit operating systems. We apologize in advance for any inconvenience, we don’t like it either. In short, the EEC chip is just not compatible with a 64-bit OS. Firmware update 2.0 is a one time only procedure. This means that once you update your EEC with the new program, you don’t have to do it again…until the next firmware update. If you happen to have a 64-bit Windows OS, you’d have to find a 32-bit OS PC to perform your update. Again, this is a one time only procedure. We’re sure there are other ways besides running to your friends and ‘borrowing’ their 32-bit for a few minutes. If you know another way, feel free to share it with everyone and post it on our forum. Let’s begin… In order to update to Firmware 2.0, you must first download the Firmware 2.0 BETA update pack (Beta 10.15.2010). Save the folder to a location you desire. Please follow both steps 1 and 2 below. Step 1 - Eagle Eye Windows Driver Installation 1. Turn the switch on the back of your EEC to "PROGRAM." 2. Plug your EEC in the USB port of your PC. - Windows will detect the EEC as a new hardware and ask you for permission to search for software. Select “No, not this time” and click “Next ” to continue. Go through with the windows Hardware Wizard. DO NOT let Windows scan for the driver. Instead, search for the driver in the "Drivers" folder located at /EEC20/EEC Firmware 2.0/Drivers/ If you get a ‘Hardware Installation’ caution message, click “Continue Anyway” To make sure the driver is installed properly, you should see “Cypress USB EZ-OTG Device” in the Device Manager under “Universal Serial Bus controllers. If you see a question mark beside the Cypress USB item, then the driver is not yet installed. To view the Device Manager click Start Control Panel System Hardware Device Manager.(For Windows XP) Step 2 - Firmware Installation 1. Locate the Sub-Folder (EEC Firmware 2.0) in your EEC20 Folder 2. Double Click on the file (bash_env1.bat). 3. Switch EEC to "PLAY" 4. Type in the following exactly as it appears qtui2c eagle1007.bin f 注意！！ FW2.0finalの場合は qtui2c eagle1111.bin f を入力 Then press Enter 5. You’ll be asked to wait; it should take about 30-90 seconds to complete. Once completed, you will see this Congratulations! You have now completed the Firmware Update. How to Perform In-Game Advance Calibration Function After completing the firmware update, your EEC will be equipped with the Advance Calibration Function to adjust the Deadzone and Sensitivity for your mouse. Tuning Mode commands F1 Enters X-axis deadzone tuning mode. (range 1-30) F2 Enters X-axis sensitivity tuning mode. (range 1-100) F3 Enters Y-axis deadzone tuning mode. (range 1-30) F4 Enters Y-axis sensitivity tuning mode. (range 1-100) F5 Save settings on Eagle Eye s EEPROM F6 Reverts back to default calibration. In Tuning Mode, use the mouse wheel to adjust the deadzone and sensitivity levels. Scroll UP to increase, DOWN decrease. Each ratchet equals one increment. During Tuning Mode, the original functions of the wheel are disabled until you press F5(save), which returns to Play mode. You will no longer be able to map F1-F6 to your PS3 controller in Eagle Edit Software. To enable the Tuning Mode, you must be in-game. Be sure to ‘feel’ the mouse movement as you adjust. Once you are in-game, follow these steps (assuming you are using Key Map 1) Step 1 Press F2 to enter Tuning Mode for the x-axis sensitivity. Scroll UP to increase the sensitivity for the x-axis. Scroll DOWN to decrease the sensitivity. Step 2 Press F4 to enter Tuning Mode for the y-axis sensitivity. Scroll UP to increase the sensitivity for the y-axis. Scroll DOWN to decrease the sensitivity. Step 3 Press F1 to enter Tuning Mode for the x-axis deadzone. Scroll UP to increase adjustment. Scroll DOWN to decrease. Step 4 Press F3 to enter Tuning Mode for the y-axis deadzone. Scroll UP to increase adjustment. Scroll DOWN to decrease. Step 5 Once you’re comfortable with the mouse movement, press F5 to save your adjustment settings. Note To calibrate the mouse for Key Map 2, you must first store the calibration into the EEC for Key Map 1. To do this; unplug the EEC from your PS3, wait 3 seconds, then plug it back in. Now switch your EEC to Key Map 2 and repeat steps 1-5 for the calibration adjustment process. Tips 1) If you are using a mouse with a DPI of 3200 or higher, try to keep the sensitivity at 10 or lower. 2) If applicable Disable all macro and/or keyboard-simulate functions on your mouse before use with the EEC. 3) For a smoother mouse movement Start off by adjusting the Sensitivity. Then, set the Deadzone increment by a multiple of your sensitivity. Example If X/Y sensitivity is 8, set X/Y deadzone to 16, 24, 32, 40, 48, etc. If X/Y sensitivity is 5, set X/Y deadzone to 10, 15, 20, 25, 30, you get the point. Original factory default setting for firmware 1.0 is the following X/Y sensitivity is set to 8, X/Y deadzone is set to 48. 4) Lower all attributes to 1 to start the calibration by pressing F1 and scrolling repeatedly downwards. Repeat the same for F2-F4. Slowly increase the sensitivity (F2 and F4 equally) first to a desired speed. Then move on to the deadzones (F1 and F3) and increase the deadzone to your desired gaming performance. New in Eagle Edit 2.0 and Steps to Synchronize your In-game Advance Calibration Settings New in Eagle Edit 2.0 Software 1. Allow you to synchronize in-game advance calibration. Click File Synchronization to load your saved calibration. 2. Pressing Send to Device will prompt you to choose between Key Map 1 or Key Map 2 memory slot. Previously, the selection was done before you press Send to Device. 3. New deadzone and sensitivity adjustments could be done in Eagle Edit 2.0 software. 4. Can now map up to 9 mouse buttons. 5. F1-F6 is now reserved for in-game Advance Calibration and could no longer be used to map to PS3 buttons. Synchronize Your In-game Advance Calibration Setting Step 1 Pause the game and unplug the EEC from your PS3. Step 2 Unplug the keyboard and mouse from your PS3. Step 3 Plug the EEC into your PC and open Eagle_Edit 2.0. Step 4 Click File Synchronization to load your saved calibration. At this point, you can save your calibration settings into the Save file. Accumulate and organize your different mapping schemes and calibrations to each specific game. Updated October 25th, 2010 Eagle Firmware 2.0 Beta with DeadZone Naturalization Bug Fixes (Updated 10.25.2010) To update to the new Firmware 2.0 Beta with Deadzone Neutralization function and fixes below, please download the new "Eagle Firmware 2.0 Beta with Deadzone Neutralization..." update above and follow the "Firmware Update Procedures" 1-4 above. Instead of typing qtui2c eagle1007.bin f at step 4, please type qtui2c eagle1025.bin f in the DOS prompt. Bug Fixes and Improvements 1. Fixed issues where F11-F12 previously could not be mapped. 2. Auto Tab no longer occurs in Eagle Edit 2.0, F8 skipping error eliminated. 3. Fixed spelling errors in Eagle Edit 2.0. 4. Refresh Rate reset to Eagle 1.0 Level – Results in firmware 1.0 mouse movement. 5. Fixed Eagle Edit 2.0 Horizontal bar scrolling issue. 6. Implemented jagged edges reduction. 7. Added Deadzone Neutralization function. Deadzone Neutralization The new version of Eagle Edit 2.0 Beta now contains a Deadzone Neutralization function. Please see following instructions 1. When you are in-game, press F1(X-axis Deadzone) and scroll your mouse wheel up several times until you see the crosshair automatically move to the right. 2. Start scrolling down slowly, 1-2 mouse clicks at a time until you see the crosshair COMPLETELY stops. We suggest you zoom-in and carefully look at the crosshair s micro movements during this stage to get the most accurate results. 3. When you come to a complete stop, you have successfully neutralized your X-axis Deadzone. 4. Press F3(Y-axis Deadzone) and repeat steps to neutralize the Y-axis Deadzone. You ll see the crosshair automatically move up 5. Once completed, adjust your sensitivity. You might notice for some games that the x-axis is more sensitive than the y, or vise versa. You may want to increase the sensitivity of the slower axis in that case. 6. Press F5 to Save your new X/Y Deadzone and sensitivity. More tips on adjusting your deadzones and sensitivity 1. Adjust the Deadzones first before you adjust the Sensitivity within the Eagle Eye. 2. If you feel that you have to adjust the Sensitivity of your mouse, tweak it as best as you can in-game, meaning tweak your game s sensitivity first. Then, use the EEC s Sensitivity function to fine-tune your mouse movements. Pending Issues We noticed an occasional mouse hiccup in the new firmware. This requires further investigation. Revert back to the original Eagle Eye firmware 1.0 eagle.bin If you wish to revert back to firmware version 1.0, please download the firmware 1.0 software eagle.bin above. Save the eagle.bin file to your EEC Firmware 2.0 Folder and follow procedures 1-4 above. Instead of typing qtui2c eagle1007.bin f at step 4 above, please type qtui2c eagle.bin f in the DOS prompt.
https://w.atwiki.jp/eagleeye/pages/25.html
Firmware Update Procedures Note The EagleEye Converter (EEC) currently does not support the firmware update procedure for Windows 64-bit operating systems. We apologize in advance for any inconvenience, we don’t like it either. In short, the EEC chip is just not compatible with a 64-bit OS. Firmware update 2.0 is a one time only procedure. This means that once you update your EEC with the new program, you don’t have to do it again…until the next firmware update. If you happen to have a 64-bit Windows OS, you’d have to find a 32-bit OS PC to perform your update. Again, this is a one time only procedure. We’re sure there are other ways besides running to your friends and ‘borrowing’ their 32-bit for a few minutes. If you know another way, feel free to share it with everyone and post it on our forum. Let’s begin… In order to update to Firmware 2.0, you must first download the Firmware 2.0 BETA update pack (Beta 10.15.2010). Save the folder to a location you desire. Please follow both steps 1 and 2 below. Step 1 - Eagle Eye Windows Driver Installation 1. Turn the switch on the back of your EEC to "PROGRAM." 2. Plug your EEC in the USB port of your PC. - Windows will detect the EEC as a new hardware and ask you for permission to search for software. Select “No, not this time” and click “Next ” to continue. Go through with the windows Hardware Wizard. DO NOT let Windows scan for the driver. Instead, search for the driver in the "Drivers" folder located at /EEC20/EEC Firmware 2.0/Drivers/ If you get a ‘Hardware Installation’ caution message, click “Continue Anyway” To make sure the driver is installed properly, you should see “Cypress USB EZ-OTG Device” in the Device Manager under “Universal Serial Bus controllers. If you see a question mark beside the Cypress USB item, then the driver is not yet installed. To view the Device Manager click Start Control Panel System Hardware Device Manager.(For Windows XP) Step 2 - Firmware Installation 1. Locate the Sub-Folder (EEC Firmware 2.0) in your EEC20 Folder 2. Double Click on the file (bash_env1.bat). 3. Switch EEC to "PLAY" 4. Type in the following exactly as it appears qtui2c eagle1007.bin f Then press Enter 5. You’ll be asked to wait; it should take about 30-90 seconds to complete. Once completed, you will see this Congratulations! You have now completed the Firmware Update. How to Perform In-Game Advance Calibration Function After completing the firmware update, your EEC will be equipped with the Advance Calibration Function to adjust the Deadzone and Sensitivity for your mouse. Tuning Mode commands F1 Enters X-axis deadzone tuning mode. (range 1-30) F2 Enters X-axis sensitivity tuning mode. (range 1-100) F3 Enters Y-axis deadzone tuning mode. (range 1-30) F4 Enters Y-axis sensitivity tuning mode. (range 1-100) F5 Save settings on Eagle Eye s EEPROM F6 Reverts back to default calibration. In Tuning Mode, use the mouse wheel to adjust the deadzone and sensitivity levels. Scroll UP to increase, DOWN decrease. Each ratchet equals one increment. During Tuning Mode, the original functions of the wheel are disabled until you press F5(save), which returns to Play mode. You will no longer be able to map F1-F6 to your PS3 controller in Eagle Edit Software. To enable the Tuning Mode, you must be in-game. Be sure to ‘feel’ the mouse movement as you adjust. Once you are in-game, follow these steps (assuming you are using Key Map 1) Step 1 Press F2 to enter Tuning Mode for the x-axis sensitivity. Scroll UP to increase the sensitivity for the x-axis. Scroll DOWN to decrease the sensitivity. Step 2 Press F4 to enter Tuning Mode for the y-axis sensitivity. Scroll UP to increase the sensitivity for the y-axis. Scroll DOWN to decrease the sensitivity. Step 3 Press F1 to enter Tuning Mode for the x-axis deadzone. Scroll UP to increase adjustment. Scroll DOWN to decrease. Step 4 Press F3 to enter Tuning Mode for the y-axis deadzone. Scroll UP to increase adjustment. Scroll DOWN to decrease. Step 5 Once you’re comfortable with the mouse movement, press F5 to save your adjustment settings. Note To calibrate the mouse for Key Map 2, you must first store the calibration into the EEC for Key Map 1. To do this; unplug the EEC from your PS3, wait 3 seconds, then plug it back in. Now switch your EEC to Key Map 2 and repeat steps 1-5 for the calibration adjustment process. Tips 1) If you are using a mouse with a DPI of 3200 or higher, try to keep the sensitivity at 10 or lower. 2) If applicable Disable all macro and/or keyboard-simulate functions on your mouse before use with the EEC. 3) For a smoother mouse movement Start off by adjusting the Sensitivity. Then, set the Deadzone increment by a multiple of your sensitivity. Example If X/Y sensitivity is 8, set X/Y deadzone to 16, 24, 32, 40, 48, etc. If X/Y sensitivity is 5, set X/Y deadzone to 10, 15, 20, 25, 30, you get the point. Original factory default setting for firmware 1.0 is the following X/Y sensitivity is set to 8, X/Y deadzone is set to 48. 4) Lower all attributes to 1 to start the calibration by pressing F1 and scrolling repeatedly downwards. Repeat the same for F2-F4. Slowly increase the sensitivity (F2 and F4 equally) first to a desired speed. Then move on to the deadzones (F1 and F3) and increase the deadzone to your desired gaming performance. New in Eagle Edit 2.0 and Steps to Synchronize your In-game Advance Calibration Settings New in Eagle Edit 2.0 Software 1. Allow you to synchronize in-game advance calibration. Click File Synchronization to load your saved calibration. 2. Pressing Send to Device will prompt you to choose between Key Map 1 or Key Map 2 memory slot. Previously, the selection was done before you press Send to Device. 3. New deadzone and sensitivity adjustments could be done in Eagle Edit 2.0 software. 4. Can now map up to 9 mouse buttons. 5. F1-F6 is now reserved for in-game Advance Calibration and could no longer be used to map to PS3 buttons. Synchronize Your In-game Advance Calibration Setting Step 1 Pause the game and unplug the EEC from your PS3. Step 2 Unplug the keyboard and mouse from your PS3. Step 3 Plug the EEC into your PC and open Eagle_Edit 2.0. Step 4 Click File Synchronization to load your saved calibration. At this point, you can save your calibration settings into the Save file. Accumulate and organize your different mapping schemes and calibrations to each specific game. Updated October 25th, 2010 Eagle Firmware 2.0 Beta with DeadZone Naturalization Bug Fixes (Updated 10.25.2010) To update to the new Firmware 2.0 Beta with Deadzone Neutralization function and fixes below, please download the new "Eagle Firmware 2.0 Beta with Deadzone Neutralization..." update above and follow the "Firmware Update Procedures" 1-4 above. Instead of typing qtui2c eagle1007.bin f at step 4, please type qtui2c eagle1025.bin f in the DOS prompt. Bug Fixes and Improvements 1. Fixed issues where F11-F12 previously could not be mapped. 2. Auto Tab no longer occurs in Eagle Edit 2.0, F8 skipping error eliminated. 3. Fixed spelling errors in Eagle Edit 2.0. 4. Refresh Rate reset to Eagle 1.0 Level – Results in firmware 1.0 mouse movement. 5. Fixed Eagle Edit 2.0 Horizontal bar scrolling issue. 6. Implemented jagged edges reduction. 7. Added Deadzone Neutralization function. Deadzone Neutralization The new version of Eagle Edit 2.0 Beta now contains a Deadzone Neutralization function. Please see following instructions 1. When you are in-game, press F1(X-axis Deadzone) and scroll your mouse wheel up several times until you see the crosshair automatically move to the right. 2. Start scrolling down slowly, 1-2 mouse clicks at a time until you see the crosshair COMPLETELY stops. We suggest you zoom-in and carefully look at the crosshair s micro movements during this stage to get the most accurate results. 3. When you come to a complete stop, you have successfully neutralized your X-axis Deadzone. 4. Press F3(Y-axis Deadzone) and repeat steps to neutralize the Y-axis Deadzone. You ll see the crosshair automatically move up 5. Once completed, adjust your sensitivity. You might notice for some games that the x-axis is more sensitive than the y, or vise versa. You may want to increase the sensitivity of the slower axis in that case. 6. Press F5 to Save your new X/Y Deadzone and sensitivity. More tips on adjusting your deadzones and sensitivity 1. Adjust the Deadzones first before you adjust the Sensitivity within the Eagle Eye. 2. If you feel that you have to adjust the Sensitivity of your mouse, tweak it as best as you can in-game, meaning tweak your game s sensitivity first. Then, use the EEC s Sensitivity function to fine-tune your mouse movements. Pending Issues We noticed an occasional mouse hiccup in the new firmware. This requires further investigation. Revert back to the original Eagle Eye firmware 1.0 eagle.bin If you wish to revert back to firmware version 1.0, please download the firmware 1.0 software eagle.bin above. Save the eagle.bin file to your EEC Firmware 2.0 Folder and follow procedures 1-4 above. Instead of typing qtui2c eagle1007.bin f at step 4 above, please type qtui2c eagle.bin f in the DOS prompt.
https://w.atwiki.jp/eagleeye/pages/24.html
Firmware Update Procedures Note The EagleEye Converter (EEC) currently does not support the firmware update procedure for Windows 64-bit operating systems. We apologize in advance for any inconvenience, we don’t like it either. In short, the EEC chip is just not compatible with a 64-bit OS. Firmware update 2.0 is a one time only procedure. This means that once you update your EEC with the new program, you don’t have to do it again…until the next firmware update. If you happen to have a 64-bit Windows OS, you’d have to find a 32-bit OS PC to perform your update. Again, this is a one time only procedure. We’re sure there are other ways besides running to your friends and ‘borrowing’ their 32-bit for a few minutes. If you know another way, feel free to share it with everyone and post it on our forum. Let’s begin… In order to update to Firmware 2.0, you must first download the Firmware 2.0 BETA update pack (Beta 10.15.2010). Save the folder to a location you desire. Please follow both steps 1 and 2 below. Step 1 - Eagle Eye Windows Driver Installation 1. Turn the switch on the back of your EEC to "PROGRAM." 2. Plug your EEC in the USB port of your PC. - Windows will detect the EEC as a new hardware and ask you for permission to search for software. Select “No, not this time” and click “Next ” to continue. Go through with the windows Hardware Wizard. DO NOT let Windows scan for the driver. Instead, search for the driver in the "Drivers" folder located at /EEC20/EEC Firmware 2.0/Drivers/ If you get a ‘Hardware Installation’ caution message, click “Continue Anyway” To make sure the driver is installed properly, you should see “Cypress USB EZ-OTG Device” in the Device Manager under “Universal Serial Bus controllers. If you see a question mark beside the Cypress USB item, then the driver is not yet installed. To view the Device Manager click Start Control Panel System Hardware Device Manager.(For Windows XP) Step 2 - Firmware Installation 1. Locate the Sub-Folder (EEC Firmware 2.0) in your EEC20 Folder 2. Double Click on the file (bash_env1.bat). 3. Switch EEC to "PLAY" 4. Type in the following exactly as it appears qtui2c eagle1007.bin f Then press Enter 5. You’ll be asked to wait; it should take about 30-90 seconds to complete. Once completed, you will see this Congratulations! You have now completed the Firmware Update. How to Perform In-Game Advance Calibration Function After completing the firmware update, your EEC will be equipped with the Advance Calibration Function to adjust the Deadzone and Sensitivity for your mouse. Tuning Mode commands F1 Enters X-axis deadzone tuning mode. (range 1-30) F2 Enters X-axis sensitivity tuning mode. (range 1-100) F3 Enters Y-axis deadzone tuning mode. (range 1-30) F4 Enters Y-axis sensitivity tuning mode. (range 1-100) F5 Save settings on Eagle Eye s EEPROM F6 Reverts back to default calibration. In Tuning Mode, use the mouse wheel to adjust the deadzone and sensitivity levels. Scroll UP to increase, DOWN decrease. Each ratchet equals one increment. During Tuning Mode, the original functions of the wheel are disabled until you press F5(save), which returns to Play mode. You will no longer be able to map F1-F6 to your PS3 controller in Eagle Edit Software. To enable the Tuning Mode, you must be in-game. Be sure to ‘feel’ the mouse movement as you adjust. Once you are in-game, follow these steps (assuming you are using Key Map 1) Step 1 Press F2 to enter Tuning Mode for the x-axis sensitivity. Scroll UP to increase the sensitivity for the x-axis. Scroll DOWN to decrease the sensitivity. Step 2 Press F4 to enter Tuning Mode for the y-axis sensitivity. Scroll UP to increase the sensitivity for the y-axis. Scroll DOWN to decrease the sensitivity. Step 3 Press F1 to enter Tuning Mode for the x-axis deadzone. Scroll UP to increase adjustment. Scroll DOWN to decrease. Step 4 Press F3 to enter Tuning Mode for the y-axis deadzone. Scroll UP to increase adjustment. Scroll DOWN to decrease. Step 5 Once you’re comfortable with the mouse movement, press F5 to save your adjustment settings. Note To calibrate the mouse for Key Map 2, you must first store the calibration into the EEC for Key Map 1. To do this; unplug the EEC from your PS3, wait 3 seconds, then plug it back in. Now switch your EEC to Key Map 2 and repeat steps 1-5 for the calibration adjustment process. Tips 1) If you are using a mouse with a DPI of 3200 or higher, try to keep the sensitivity at 10 or lower. 2) If applicable Disable all macro and/or keyboard-simulate functions on your mouse before use with the EEC. 3) For a smoother mouse movement Start off by adjusting the Sensitivity. Then, set the Deadzone increment by a multiple of your sensitivity. Example If X/Y sensitivity is 8, set X/Y deadzone to 16, 24, 32, 40, 48, etc. If X/Y sensitivity is 5, set X/Y deadzone to 10, 15, 20, 25, 30, you get the point. Original factory default setting for firmware 1.0 is the following X/Y sensitivity is set to 8, X/Y deadzone is set to 48. 4) Lower all attributes to 1 to start the calibration by pressing F1 and scrolling repeatedly downwards. Repeat the same for F2-F4. Slowly increase the sensitivity (F2 and F4 equally) first to a desired speed. Then move on to the deadzones (F1 and F3) and increase the deadzone to your desired gaming performance. New in Eagle Edit 2.0 and Steps to Synchronize your In-game Advance Calibration Settings New in Eagle Edit 2.0 Software 1. Allow you to synchronize in-game advance calibration. Click File Synchronization to load your saved calibration. 2. Pressing Send to Device will prompt you to choose between Key Map 1 or Key Map 2 memory slot. Previously, the selection was done before you press Send to Device. 3. New deadzone and sensitivity adjustments could be done in Eagle Edit 2.0 software. 4. Can now map up to 9 mouse buttons. 5. F1-F6 is now reserved for in-game Advance Calibration and could no longer be used to map to PS3 buttons. Synchronize Your In-game Advance Calibration Setting Step 1 Pause the game and unplug the EEC from your PS3. Step 2 Unplug the keyboard and mouse from your PS3. Step 3 Plug the EEC into your PC and open Eagle_Edit 2.0. Step 4 Click File Synchronization to load your saved calibration. At this point, you can save your calibration settings into the Save file. Accumulate and organize your different mapping schemes and calibrations to each specific game. Updated October 25th, 2010 Eagle Firmware 2.0 Beta with DeadZone Naturalization Bug Fixes (Updated 10.25.2010) To update to the new Firmware 2.0 Beta with Deadzone Neutralization function and fixes below, please download the new "Eagle Firmware 2.0 Beta with Deadzone Neutralization..." update above and follow the "Firmware Update Procedures" 1-4 above. Instead of typing qtui2c eagle1007.bin f at step 4, please type qtui2c eagle1025.bin f in the DOS prompt. Bug Fixes and Improvements 1. Fixed issues where F11-F12 previously could not be mapped. 2. Auto Tab no longer occurs in Eagle Edit 2.0, F8 skipping error eliminated. 3. Fixed spelling errors in Eagle Edit 2.0. 4. Refresh Rate reset to Eagle 1.0 Level – Results in firmware 1.0 mouse movement. 5. Fixed Eagle Edit 2.0 Horizontal bar scrolling issue. 6. Implemented jagged edges reduction. 7. Added Deadzone Neutralization function. Deadzone Neutralization The new version of Eagle Edit 2.0 Beta now contains a Deadzone Neutralization function. Please see following instructions 1. When you are in-game, press F1(X-axis Deadzone) and scroll your mouse wheel up several times until you see the crosshair automatically move to the right. 2. Start scrolling down slowly, 1-2 mouse clicks at a time until you see the crosshair COMPLETELY stops. We suggest you zoom-in and carefully look at the crosshair s micro movements during this stage to get the most accurate results. 3. When you come to a complete stop, you have successfully neutralized your X-axis Deadzone. 4. Press F3(Y-axis Deadzone) and repeat steps to neutralize the Y-axis Deadzone. You ll see the crosshair automatically move up 5. Once completed, adjust your sensitivity. You might notice for some games that the x-axis is more sensitive than the y, or vise versa. You may want to increase the sensitivity of the slower axis in that case. 6. Press F5 to Save your new X/Y Deadzone and sensitivity. More tips on adjusting your deadzones and sensitivity 1. Adjust the Deadzones first before you adjust the Sensitivity within the Eagle Eye. 2. If you feel that you have to adjust the Sensitivity of your mouse, tweak it as best as you can in-game, meaning tweak your game s sensitivity first. Then, use the EEC s Sensitivity function to fine-tune your mouse movements. Pending Issues We noticed an occasional mouse hiccup in the new firmware. This requires further investigation. Revert back to the original Eagle Eye firmware 1.0 eagle.bin If you wish to revert back to firmware version 1.0, please download the firmware 1.0 software eagle.bin above. Save the eagle.bin file to your EEC Firmware 2.0 Folder and follow procedures 1-4 above. Instead of typing qtui2c eagle1007.bin f at step 4 above, please type qtui2c eagle.bin f in the DOS prompt.
https://w.atwiki.jp/eagleeye/pages/13.html
Eagle Edit Software Eagle Eye Edit Software Download V1.0 (Updated 8.18.2010) Eagle Eye Edit Software V.2.0 Download Only EagleEdit20.RAR (Updated 10.12.2010) Firmware 2.0 Update (October 15th, 2010) (Beta) Update内容 Firmware 2.0 BETA update pack (Beta 10.15.2010) こちらもあわせてごらんください セットアップ、FW Update 動画(英語)
https://w.atwiki.jp/eagleeye/pages/14.html
UNPACK Eagle Eye Mouse Keyboard Converter for PS3 EEC 商品概要 E3 2010 Eagle Eye Converter E3 2010でのようす Firmware 2.0 FWのUpdate実演 Part 1(setup) of the Video Introduction on the Eagle Eye Converter EECのセットアップ Pt.1 Part 2(Game Play) of the Video introduction on the PS3 Eagle Eye Converter EECのセットアップ Pt.2 "ゲームプレイ編" Eagle Eye Converter for PS3 COD MW2/MafiaII TEST (With Logicool G500) EECでのゲームプレイ実演 COD MW2/MafiaII マウス Logicool G500 Eagle Eye PS3 Review - Convert Mouse Keyboard into PS3 Controller EECレビュー(開封からプレイまで一連の流れ)
https://w.atwiki.jp/eagleeye/pages/16.html
Firmware 2.0 Update details Multiple Mouse Button Support – Supports scroll wheel, tilt, and 2 side buttons. Map the scroll wheel up and down, scroll wheel tilt left and right, and 2 side buttons. Eagle Edit V.2.0 – Improved GUI and layout, Thank you GAZA for contributing this new graphic interface for our Eagle Edit program. The new Eagle Edit V.2.0 will compliment the new Advance Calibration function, allowing you to download the Dead zone/Sensitivity setting you programming during game as a file to be saved and used later, or share with the gaming community. Advance Calibration (mouse deadzone/sensitivity adjustments) – One of the most important improvement for Eagle Eye Firmware V2.1. Allowing you to increase/decrease the X Y dead zone and sensitivity during game play to find that perfect setting. Save this setting and download it using Eagle Edit V.2.0 for future use and share it with your friends the Eagle Eye community. Rapid Fire Controller Function – When you plug in your EEC to your PS3, then your regular duel shock ps3 controller to either the mouse/keyboard USB slot on the EEC, you can turn your PS3 controller into a turbo controller. Advanced Calibration Function for the Mouse Version 2.0 If applicable Disable all macro and/or keyboard-simulate functions on your mouse before use with the EEC. Adjust the X-axis and Y-axis deadzone. Adjust the X/Y-axis sensitivity during gameplay and save your settings. Detailed information F1 Enters X-axis deadzone tuning mode. F2 Enters X-axis sensitivity tuning mode. F3 Enters Y-axis deadzone tuning mode. F4 Enters Y-axis sensitivity tuning mode. F5 Save settings on Eagle-eye s EEPROM F6 Restore all X/Y-axis sensitivity and deadzone to factory default. Assume the x-axis physical mouse movement is X, the x-axis movement in game Dx would be Dx = sensitivity * X + deadzone Similarly Dy = sensitivity * Y + deadzone In Tuning Mode, use the mouse wheel to adjust the deadzone and sensitivity. Scroll UP to increase, DOWN decrease. Each ratchet equals one increment. During Tuning Mode, the original functions of the wheel are disabled until you press F5(save), which returns to Play mode. View your saved settings in Eagle_Edit on your PC. F1-F6 are now reserved for the Tuning Mode keys and therefore cannot be used in keymapping. New to Firmware 2.0 1. Added Advanced Calibration Functions 2. New Eagle Edit 2.0 3. Improved Compatibility with Razer Mice Fixes From Beta 10/25 1. Fix tilt not mappable in Eagle-eidt. You need to use ctrl+right arrow / left arrow to assign them now. 2. Fix side button reverse 3. Fix Save As problem under XP 4. Fix a bug that mouse wheel will auto trigger on a key stroke. Know Issues and Bugs 1. Mouse Hiccup for some mouse 2. Auto Melee or Start Button 3. Firmware update in x64 environment not available 4. A Firmware updater program 5. Additional mouse compatibility
https://w.atwiki.jp/qweasdrtyfgh/
@wikiへようこそ ウィキはみんなで気軽にホームページ編集できるツールです。 このページは自由に編集することができます。 メールで送られてきたパスワードを用いてログインすることで、各種変更（サイト名、トップページ、メンバー管理、サイドページ、デザイン、ページ管理、等）することができます まずはこちらをご覧ください。 @wikiの基本操作 用途別のオススメ機能紹介 @wikiの設定/管理 分からないことは？ @wiki ご利用ガイド よくある質問 無料で会員登録できるSNS内の@wiki助け合いコミュニティ @wiki更新情報 @wikiへのお問合せフォーム 等をご活用ください @wiki助け合いコミュニティの掲示板スレッド一覧 #atfb_bbs_list その他お勧めサービスについて 大容量１Ｇ、PHP/CGI、MySQL、FTPが使える無料ホームページは@PAGES 無料ブログ作成は@WORDをご利用ください 2ch型の無料掲示板は@chsをご利用ください フォーラム型の無料掲示板は@bbをご利用ください お絵かき掲示板は@paintをご利用ください その他の無料掲示板は@bbsをご利用ください 無料ソーシャルプロフィールサービス @flabo(アットフラボ) おすすめ機能 気になるニュースをチェック 関連するブログ一覧を表示 その他にもいろいろな機能満載！！ @wikiプラグイン @wiki便利ツール @wiki構文 @wikiプラグイン一覧 まとめサイト作成支援ツール バグ・不具合を見つけたら？ 要望がある場合は？ お手数ですが、メールでお問い合わせください。